Informații
  • Codurile de eroare ale motorului

Codurile de eroare ale motorului

Motorul "NO RESTART". Dacă apare acest mesaj, motorul va continua să funcționeze pentru a permite mașinilor să se deplaseze într-o poziție sigură în care mașina poate fi reparată. Odată ce motorul s-a oprit, acesta nu va porni din nou până când reparația nu este finalizată.

Dacă este afișat mesajul "LOW POWER" (Putere redusă), puterea motorului este redusă la 60% pentru a proteja motorul.

Error Codes ( Error Displayed )            Use for identification the repair part                   
  • DTC       Diagnostic Monitoring Item (Malfunction Title)     Condition for Setting DTC
  • P0087     Fuel rail pressure is too low (Fuel leak)     Actual rail pressure < Minimum target rail pressure at actual rail pressure is 15MPa or more
  • P0088     Common rail pressure (1st stage)     Rail pressure is over 185MPa
  • P0088     Common rail pressure (2nd stage)     Common rail pressure failure (1st. Stage) is occurred and the rail pressure is over 190MPa.
  • P0089     Common rail pressure (excessive pressure for pump)     DUTY for SCV is 40% or more. Or Actual rail press -Target rail press >40MPa~ then target fuel flow is 90mm 3/st or less.
  • P0090     Fuel pressure regulator control circuit     SCV driving current > 2400mA or 50mA < SCV driving current, or Target current - Actual current >1000 mA
  • P0107     Air pressure sensor (low voltage)     The voltage of air pressure temperature sensor falls below 0.099V.
  • P0108     Air pressure sensor (high voltage)     The voltage of air pressure temperature sensor exceeds 4.85V.
  • P0112     Intake air temperature circuit (low voltage)     The voltage of intake temperature sensor falls below 0.099V.
  • P0113     Intake air temperature circuit (high voltage)     The voltage of intake temperature sensor exceeds 4.85V.
  • P0117     Engine coolant temperature circuit (low voltage)     The voltage of water temperature sensor falls below 0.099V.
  • P0118     Engine coolant temperature circuit (high voltage)     The voltage of water temperature sensor exceeds 4.85V.
  • P0182     Fuel temperature sensor circuit (low voltage)     The voltage of fuel temperature sensor falls below 0.099V.
  • P0183     Fuel temperature sensor circuit (high voltage)     The voltage of fuel temperature sensor exceeds 4.85V.
  • P0192     Fuel rail pressure sensor circuit (low voltage)     The voltage of common rail pressure sensor falls below 0.7V.
  • P0193     Fuel rail pressure sensor circuit (high voltage)     The voltage of common rail pressure sensor exceeds 4.5V.
  • P0201     Injector circuit cylinder 1     Input signal at inj. No.1 is not active
  • P0202     Injector circuit cylinder 2     Input signal at inj. No.2 is not active
  • P0203     Injector circuit cylinder 3     Input signal at inj. No.3 is not active
  • P0204     Injector circuit cylinder 4     Input signal at inj. No.4 is not active
  • P0205     Injector circuit cylinder 5     Input signal at inj. No.5 is not active
  • P0206     Injector circuit cylinder 6     Input signal at inj. No.6 is not active
  • P0219     Over run     Engine speed exceeds 2300 rpm (In case of 6HK1)
  • P0237     Boost pressure sensor (low voltage)     The voltage of boost pressure sensor falls below 0.099V.
  • P0238     Boost pressure sensor (high voltage)     The voltage of boost pressure sensor exceeds 4.85V.
  • P0335     Crank sensor (no signal)     Cam signal is active but Crank signal is not active.
  • P0336     Crank sensor (signal error)     Discrepancy in base crank signal pulse rate
  • P0340     Cam sensor (no signal)     Crank signal is active but Cam signal is not active.
  • P0341     Cam sensor (signal error)     Discrepancy in base Cam signal pulse rate
  • P0380     Glow relay     No signal of Glow Relay Monitor against the instruction of Glow Relay Driving at the IGKEY power voltage is 16V- 32V.
  • P0381     Glow lamp     No signal of Glow Lamp monitoring against instruction for lighting glow lamp.
  • P0487     EGR positioning signal error (brush less spec.)     Output signal of EGR Valve position sensor is out of the range.
  • P0488     EGR valve control failure     The rate difference between target valve lift and the actual position is 20% or more.
  • P0522     Engine oil pressure sensor (Low voltage irregular)     The oil pressure sensor falls below 0.099V.
  • P0523     Engine oil pressure sensor (High voltage irregular)     The oil pressure sensor exceeds 4.85V.
  • P0601     ROM     ROM error
  • P0603     EEPROM     EEPROM error
  • P0606     CPU     Sub CPU detected the failure of main CPU.
  • P0606     IC for CPU detection     RUN-SUB pulse doesn't change for 20msec or more.
  • P0611     ECM Charge circuit 1 (Low Voltage)     The voltage in ECU charge circuit 1 is low.
  • P0612     ECM Charge circuit 2 (Low Voltage)     The voltage in ECU charge circuit 2 is low.
  • P1093     Fuel rail pressure is low during power enrichment. (Fuel leak)     At fuel rail pressure Qty. = 28000mm 3/st or more, Target rail pressure - Actual rail pressure >15MPa
  • P1095     Pressure limiter open     Pressure limiter is opened
  • P1112     Boost temperature sensor (Low voltage irregular)     The voltage of boost temperature sensor falls below 0.099V.
  • P1113     Boost temperature sensor (High voltage irregular)     The voltage of boost temperature sensor exceeds 4.85V at water temperature exceeds 50°C or more, or  > 5 minutes past since Key On.
  • P1173     Over heat     Water temperature exceeds 120°C at engine running.
  • P1261     Injector circuit group 1     No monitoring input signal from Inj. 1 & 4 1 & 2 & 3
  • P1262     Injector circuit group 2     No monitoring input signal from Inj. 2 & 3 4 & 5 & 6
  • P1271     Accel sensor circuit 1-2 correlation     The difference of accelsensor open-rate between No.1 and No.2 is more than 45%.
  • P1272     Accel sensor circuit 2-3 correlation     The difference of accelsensor open-rate between No.2 and No.3 is more than 45%.
  • P1273     Accel sensor circuit 1-3 correlation     The difference of accelsensor open-rate between No.1 and No.3 is more than 45%.
  • P1277     Accel sensor circuit 1 (low input)     The voltage of accel sensor No.1 falls below 0.199V.
  • P1278     Accel sensor circuit 1 (high input)     The voltage of accel sensor No.1 exceeds 4.9V.
  • P1282     Accel sensor circuit 2 (low input)     The voltage of accel sensor No.2 falls below 0.199V.
  • P1283     Accel sensor circuit 2 (high input)     The voltage of accel sensor No.2 exceeds 4.9V.
  • P1287     Accel sensor circuit 3 (low input)     The voltage of accel sensor No.3 falls below 0.199V.
  • P1288     Accel sensor circuit 3 (high input)     The voltage of accel sensor No.3 exceeds 4.9V.
  • P1345     Cam&Crank sensor pulse phase (Phase difference)     Difference Cam pulse is beside the Crank gap position
  • P1625     Main relay circuit     Output of Main relay coils: On, and the voltage of main relay line is 1V or less.
  • P1625     Main relay circuit     Output of Main relay coils: Off, and the voltage of main relay line is 18V or more.
  • P1630     A/D conversion     A/D does not convert.
  • P1631     5 Volt reference 1 circuit     IGKEY power battery is 5.5 V or more, or 4.5 V or less at the battery voltage range:16V~32V.
  • P1632     5 Volt reference 2 circuit     IGKEY power battery is 5.5 V or more, or 4.5 V or less at the battery voltage range:16V~32V.
  • P1633     5 Volt reference 3 circuit     IGKEY power battery is 5.5 V or more, or 4.5 V or less at the battery voltage range:16V~32V.
  • P1634     5 Volt reference 4 circuit     IGKEY power battery is 5.5 V or more, or 4.5 V or less at the battery voltage range:16V~32V.
  • P1635     5 Volt reference 5 circuit     IGKEY power battery is 5.5 V or more, or 4.5 V or less at the battery voltage range is from 16V to 32V.
  • U2104     CAN Bus     Bus off detection
  • U2106     CAN Time out     Lost communication for a set hours