Engine Error Codes
Engine `NO RESTART'. If this message appears theengine will continue to run to allow the machines to bemoved to a position of safety where the machine can berepaired. Once the engine is stopped it will not restart untilthe repair as been carried out.If the message `LOW POWER' displays the engine poweris reduced to 60% power to protect the engine.
Error Codes ( Error Displayed ) Use for identification the repair part
- DTC Diagnostic Monitoring Item (Malfunction Title) Condition for Setting DTC
- P0087 Fuel rail pressure is too low (Fuel leak) Actual rail pressure < Minimum target rail pressure at actual rail pressure is 15MPa or more
- P0088 Common rail pressure (1st stage) Rail pressure is over 185MPa
- P0088 Common rail pressure (2nd stage) Common rail pressure failure (1st. Stage) is occurred and the rail pressure is over 190MPa.
- P0089 Common rail pressure (excessive pressure for pump) DUTY for SCV is 40% or more. Or Actual rail press -Target rail press >40MPa~ then target fuel flow is 90mm 3/st or less.
- P0090 Fuel pressure regulator control circuit SCV driving current > 2400mA or 50mA < SCV driving current, or Target current - Actual current >1000 mA
- P0107 Air pressure sensor (low voltage) The voltage of air pressure temperature sensor falls below 0.099V.
- P0108 Air pressure sensor (high voltage) The voltage of air pressure temperature sensor exceeds 4.85V.
- P0112 Intake air temperature circuit (low voltage) The voltage of intake temperature sensor falls below 0.099V.
- P0113 Intake air temperature circuit (high voltage) The voltage of intake temperature sensor exceeds 4.85V.
- P0117 Engine coolant temperature circuit (low voltage) The voltage of water temperature sensor falls below 0.099V.
- P0118 Engine coolant temperature circuit (high voltage) The voltage of water temperature sensor exceeds 4.85V.
- P0182 Fuel temperature sensor circuit (low voltage) The voltage of fuel temperature sensor falls below 0.099V.
- P0183 Fuel temperature sensor circuit (high voltage) The voltage of fuel temperature sensor exceeds 4.85V.
- P0192 Fuel rail pressure sensor circuit (low voltage) The voltage of common rail pressure sensor falls below 0.7V.
- P0193 Fuel rail pressure sensor circuit (high voltage) The voltage of common rail pressure sensor exceeds 4.5V.
- P0201 Injector circuit cylinder 1 Input signal at inj. No.1 is not active
- P0202 Injector circuit cylinder 2 Input signal at inj. No.2 is not active
- P0203 Injector circuit cylinder 3 Input signal at inj. No.3 is not active
- P0204 Injector circuit cylinder 4 Input signal at inj. No.4 is not active
- P0205 Injector circuit cylinder 5 Input signal at inj. No.5 is not active
- P0206 Injector circuit cylinder 6 Input signal at inj. No.6 is not active
- P0219 Over run Engine speed exceeds 2300 rpm (In case of 6HK1)
- P0237 Boost pressure sensor (low voltage) The voltage of boost pressure sensor falls below 0.099V.
- P0238 Boost pressure sensor (high voltage) The voltage of boost pressure sensor exceeds 4.85V.
- P0335 Crank sensor (no signal) Cam signal is active but Crank signal is not active.
- P0336 Crank sensor (signal error) Discrepancy in base crank signal pulse rate
- P0340 Cam sensor (no signal) Crank signal is active but Cam signal is not active.
- P0341 Cam sensor (signal error) Discrepancy in base Cam signal pulse rate
- P0380 Glow relay No signal of Glow Relay Monitor against the instruction of Glow Relay Driving at the IGKEY power voltage is 16V- 32V.
- P0381 Glow lamp No signal of Glow Lamp monitoring against instruction for lighting glow lamp.
- P0487 EGR positioning signal error (brush less spec.) Output signal of EGR Valve position sensor is out of the range.
- P0488 EGR valve control failure The rate difference between target valve lift and the actual position is 20% or more.
- P0522 Engine oil pressure sensor (Low voltage irregular) The oil pressure sensor falls below 0.099V.
- P0523 Engine oil pressure sensor (High voltage irregular) The oil pressure sensor exceeds 4.85V.
- P0601 ROM ROM error
- P0603 EEPROM EEPROM error
- P0606 CPU Sub CPU detected the failure of main CPU.
- P0606 IC for CPU detection RUN-SUB pulse doesn't change for 20msec or more.
- P0611 ECM Charge circuit 1 (Low Voltage) The voltage in ECU charge circuit 1 is low.
- P0612 ECM Charge circuit 2 (Low Voltage) The voltage in ECU charge circuit 2 is low.
- P1093 Fuel rail pressure is low during power enrichment. (Fuel leak) At fuel rail pressure Qty. = 28000mm 3/st or more, Target rail pressure - Actual rail pressure >15MPa
- P1095 Pressure limiter open Pressure limiter is opened
- P1112 Boost temperature sensor (Low voltage irregular) The voltage of boost temperature sensor falls below 0.099V.
- P1113 Boost temperature sensor (High voltage irregular) The voltage of boost temperature sensor exceeds 4.85V at water temperature exceeds 50°C or more, or > 5 minutes past since Key On.
- P1173 Over heat Water temperature exceeds 120°C at engine running.
- P1261 Injector circuit group 1 No monitoring input signal from Inj. 1 & 4 1 & 2 & 3
- P1262 Injector circuit group 2 No monitoring input signal from Inj. 2 & 3 4 & 5 & 6
- P1271 Accel sensor circuit 1-2 correlation The difference of accelsensor open-rate between No.1 and No.2 is more than 45%.
- P1272 Accel sensor circuit 2-3 correlation The difference of accelsensor open-rate between No.2 and No.3 is more than 45%.
- P1273 Accel sensor circuit 1-3 correlation The difference of accelsensor open-rate between No.1 and No.3 is more than 45%.
- P1277 Accel sensor circuit 1 (low input) The voltage of accel sensor No.1 falls below 0.199V.
- P1278 Accel sensor circuit 1 (high input) The voltage of accel sensor No.1 exceeds 4.9V.
- P1282 Accel sensor circuit 2 (low input) The voltage of accel sensor No.2 falls below 0.199V.
- P1283 Accel sensor circuit 2 (high input) The voltage of accel sensor No.2 exceeds 4.9V.
- P1287 Accel sensor circuit 3 (low input) The voltage of accel sensor No.3 falls below 0.199V.
- P1288 Accel sensor circuit 3 (high input) The voltage of accel sensor No.3 exceeds 4.9V.
- P1345 Cam&Crank sensor pulse phase (Phase difference) Difference Cam pulse is beside the Crank gap position
- P1625 Main relay circuit Output of Main relay coils: On, and the voltage of main relay line is 1V or less.
- P1625 Main relay circuit Output of Main relay coils: Off, and the voltage of main relay line is 18V or more.
- P1630 A/D conversion A/D does not convert.
- P1631 5 Volt reference 1 circuit IGKEY power battery is 5.5 V or more, or 4.5 V or less at the battery voltage range:16V~32V.
- P1632 5 Volt reference 2 circuit IGKEY power battery is 5.5 V or more, or 4.5 V or less at the battery voltage range:16V~32V.
- P1633 5 Volt reference 3 circuit IGKEY power battery is 5.5 V or more, or 4.5 V or less at the battery voltage range:16V~32V.
- P1634 5 Volt reference 4 circuit IGKEY power battery is 5.5 V or more, or 4.5 V or less at the battery voltage range:16V~32V.
- P1635 5 Volt reference 5 circuit IGKEY power battery is 5.5 V or more, or 4.5 V or less at the battery voltage range is from 16V to 32V.
- U2104 CAN Bus Bus off detection
- U2106 CAN Time out Lost communication for a set hours